#X mirage active keys 64 Bit
#X mirage active keys driver
#X mirage active keys 32 bit
#X mirage active keys password

follow prompts on screen (turn ignition off, wait 2 secs, turn ignition on) press ok. Next move to engine tab, find both cruise control parameters and enable them. (In this order) plug obdII into car, plug usb into laptop, turn key on.

#X mirage active keys password

This is a different log in than the forum, put a different user name and password (recommend write both user names and passwords down, I didn't and caused problem later) and click down arrow and click register, NOT LOG IN!! (I derailed here for days) system should boot up. Once you have all that, open etacs decoder (must have internet connection to work) its going to ask you to log in again.

#X mirage active keys driver

My mini VCI cable came with a driver for the cable (x-horse) downloaded that using an external cd rom. I first went to /forum and made an account for the forum, (I READ A LOT) lots of info here, Read as much as you can, sort threads by number of views then start at the top.

#X mirage active keys 32 bit

I found info saying the 32 bit system is easier.

#X mirage active keys 64 Bit

I have heard 64 bit systems work but have no knowledge here. I have an old acer aspire one netbook with an OS: windows XP 32 bit. Other ways may work, this is how I did it. I did a ton of research and I recommend you do the same before you start this project. Now you need to change 2 parameters in your ETACS system to active the cruise control (this is where I struggled for a long time) Sounds like a lot but I was trying to be descriptive. I used it to set the nut into place but torqued by hand) Couldn't find spec I used just shy of 50 fl/lbs (use of impact gun putting wheel back on is on you. Make sure wheel is still straight and torque wheel nut back down. once nut is removed used steering wheel puller (I used my fist at the back of the wheel to break loose) Replace with new wheel my 2015 ES wheel had ground wire in same connector as cruise and radio controls. I used impact gun, use at your desecration. Also paint mark on steering wheel) remove nut, i think 17mm or 19mm cant remember. !!!!!!!!Important!!!!!!!!!!! going forward make sure steering wheel is dead nuts center, recommend paint marker at top of column (12 o'clock mark on threaded male end. Remove 2 connectors on back of airbag then remove ground wire on airbag. Pop up yellow tabs with small standard screwdriver on back of airbag. SwitchclutchĘ606A025 eBay spring to release air bag.

My car, USA 2015 Mirage 5mt DE (no cruise from the factory)Ģ015 Mirage ES steering wheel, eBay (127 shipped)īrakeswitch 8614A183 eBay (4 pin switch instead of 2 pin that's on the car) I wanted to share my success of installing factory cruise control on my Mirage DE I'll probably try to source a wheel with the radio controls but no BT buttons to keep things clean. I don't car all that much about BT, but figured it would be a nice bonus if I was planning to swap the steering wheel anyway to get cruise control functionality.

Seems like every other optional feature on this car is already prewired. That makes sense, though! I figured there would be more to it than just adding a couple buttons, but wasn't sure. This would be the simpler way to go.I don't believe my car came with BT - no buttons on the steering wheel and two switch blanks on the panel to the left of the steering wheel (only mirror controls and stability control disable are there). For those setups the buttons were on the dash near the power mirror controls. There was a also dealer or port installed(add-on) bluetooth setup for some cars. My 14 and all our 15's at work came with factory bluetooth and the mic is in the headliner near the dome light, I'm pretty sure there's also a module behind the radio towards the glovebox as well. Are you saying your car didn't come with bluetooth and you want to add it? If so you'll need more than the buttons.